研究院科研情报与新闻主站科研动态 · 行业情报 · 管理政策
2026年11月17日
首页 › 碳纤维 › 正文

Development of commingled hoop-wound composites-reinforced O-rings (CRO) for aeronautical application

Springer 2026-11-16 1 天前
Using 3D-printing resources, a hermetic mold was created to combine the composites reinforcement with the silicon-based elastomeric covering. Finally, composites reinforced O‑rings were submitted to tensile testing, based on ASTM D2290 procedures, and a comparison of the resulting mechanical properties revealed superior performance of the commingled reinforcements. Using the O‑ring made solely of
· RESEARCH · Published: Abstract Traditional elastomeric O‑rings, although widely employed in aerospace sealing applications, are often limited by its inadequate chemical resistance, thermal stability, mechanical resistance and durability under extreme operating conditions. This article proposes the development of high-performance composites for O‑ring reinforcement using carbon fiber/polyether ether ketone and glass fiber/polyamide commingled technologies engineered to address current limitations by integrating elastomeric materials with continuous reinforcements tailored for the demanding environments of aerospace systems. A novel pre-compaction device (machine head) for commingled tows was designed and developed for using at filament winding technique, which was used to manufacture the reinforcement inner section of the O‑rings. Final compaction level of commingled composites was carried out using compression molding to meet aeronautical requirements. The materials were characterized by SEM and thermal analysis as DSC. O‑ring reinforcements made from 3D-printed carbon fiber/Onyx and glass fiber/Onyx by Markforged® printer were also manufactured and tested, indicating the improvement of O‑rings performance when used commingled technology. Using 3D-printing resources, a hermetic mold was created to combine the composites reinforcement with the silicon-based elastomeric covering. Finally, composites reinforced O‑rings were submitted to tensile testing, based on ASTM D2290 procedures, and a comparison of the resulting mechanical properties revealed superior performance of the commingled reinforcements. Using the O‑ring made solely of Dowsil™ 732 as the reference, all reinforced composite O‑rings showed substantial improvements in mechanical performance. CF/PEEK CRO exhibited the greatest enhancement, with increases of approximately 16,186% in elastic modulus and 76,533% in tensile strength, while GF/PA, CF/Onyx, and GF/Onyx also achieved significant gains. These results demonstrate that internal composite reinforcement markedly improves the stiffness and tensile strength of silicone O‑rings. This is a preview of subscription content, log in via an institution to check access. Access this article Subscribe and save Springer+ from €37.37 /Month · Receive 10 units per month · Download 1 article/chapter for 1 unit · Get selected eBooks for 7 units · Cancel anytime Buy Now Price includes VAT (China (P.R.)) Instant access to the full article PDF. Data Availability No datasets were generated or analysed during the current study. References Porter C, Zaman B, Pazur R. A critical examination of the shelf life of nitrile rubber O‑Rings used in aerospace sealing applications. Polym. Degrad. Stab. 2022;206:110199. Kumar B, DeRemer D, Marshall D. An Illustrated Dictionary of Aviation. New York: McGraw-Hill; 2005. Deaconescu A, Deaconescu T. Behavioral Study of Elastomeric O‑Rings Built into Coaxial Sealing Systems. Polymers (Basel). 2025;17:1–12. Liu Y, Wilson CW. Investigation into the Temperature Impact on O‑Ring’s Sealing Performance Using Advanced Stress Relaxation Test. Appl. Mech. Mater. 2012;225:255–60. Pop GI, Titu AM, Pop AB. Enhancing Aerospace Industry Efficiency and Sustainability: Process Integration and Quality Management in the Context of Industry 4.0. Sustainability. 2023;15:1–13. Müller M, Šleger V, Čedík J, Pexa M. Research on the Material Compatibility of Elastomer Sealing O‑Rings. Polymers (Basel). 2022;14:1–9. Committee, A.-6C2 S. AIR786A - ELASTOMER COMPATIBILITY CONSIDERATIONS RELATIVE TO O‑RING AND SEALANT SELECTION. at https://doi.org/10.4271/AIR786A (1992). Chawla KK. Composite Materials: Science and Engineering. Berlin/Heidelberg: Springer Science & Business Media; 1998. Di Benedetto RM, Botelho EC, Janotti A, Ancelotti Junior AC, Gomes GF. Development of an artificial neural network for predicting energy absorption capability of thermoplastic commingled composites. Compos. Struct. 2021;257:113–31. Di Benedetto RM, Janotti A, Ancelotti Junior AC, Botelho EC. Elastic coefficients of poly(ether-etherketone) from first-principles calculations. Mater. Res. 2025;28:1–6. Mc Lauchlin AR, Ghita OR, Savage L. Studies on the reprocessability of poly(ether ether ketone) (PEEK). J. Mater. Process. Technol. 2014;214:75–80. Pan L, Yapici U. A comparative study on mechanical properties of carbon fiber/PEEK composites. Adv. Compos. Mater. 2016;25:359–74. Di Benedetto RM, Janotti AJ, Gomes GF, Ancelotti Junior AC, Botelho EC. Statistical approach to optimize crashworthiness of thermoplastic commingled composites. Mater. Today Commun. 2022;31:2352–4928. Campbell, F. C. Structural Composite Materials. (Materials Park, OH, 2010). Chang IY, Lees JK. Recent Development in Thermoplastic Composites: A Review of Matrix Systems and Processing Methods. J. Thermoplast. Compos. Mater. 1998;1:277–95. Song Q, et al. Research on Void Dynamics during In Situ Consolidation of CF/High-Performance Thermoplastic Composite. Polymers (Basel). 2022;14:1–18. Souza BR, et al. Manufacturing and Characterization of Jute/PP Thermoplastic Commingled Composite. Mater. Res. J. Mater. 2017;1:1–8. Long AC, Wilks CE, Rudd CD. Experimental characterisation of the consolidation of a commingled glass/polypropylene composite. Compos. Sci. Technol. 2001;61:1591–603. Ren P, et al. The Influence of Compression Molding Techniques on Thermal Conductivity of UHMWPE/BN and UHMWPE/(BN + MWCNT) Hybrid Composites with Segregated Structure. Compos. Part A Appl. Sci. Manuf. 2016;90:13–21. Lin HH, Ranganathan S, Advani SG. Consolidation of Continuous Fiber Systems. In: Flow and Rheology in Polymer Composites Manufacturing. Composite Materials Series, Vol. 10. 1994. pp. 320–69. Di Benedetto RM, Raponi OA, Junqueira DM, Ancelotti Junior AC. Crashworthiness and Impact Energy Absorption Study Considering the CF/PA Commingled Composite Processing Optimization. Mater. Res. 2017;20:792–9. Nayana V, Kandasubramanian B. Advanced polymeric composites via commingling for critical engineering applications. Polym. Test. 2020;91:106774. Van West BP, Pipes RB, Advani SG. The consolidation of commingled thermoplastic fabrics. Polym. Compos. 1991;12:417–27. Brasington A, Sacco C, Halbritter J, Wehbe R, Harik R. Automated fiber placement: A review of history, current technologies, and future paths forward. Compos. Part C Open Access. 2021;6:100182. Ueda M, et al. 3D compaction printing of a continuous carbon fiber reinforced thermoplastic. Compos. Part A Appl. Sci. Manuf. 2020;137:1–20. Kugler D, Moon TJ. A technique for compression testing of composite rings. Compos. Part A Appl. Sci. Manuf. 2002;33:507–14. Di Benedetto RM, et al. 3D-Printed Continuous Fiber Composites: An Overview of Materials, Systems and Processes. Adv. Mater. Sustain. Manuf. 2025;2:1–15. Leach D, McCrea T, Chamberlain C. Cost Effective Thermoplastic Composites in Aerostructures. Sample J. 2022;1:1–20. Karahan M, et al. Comparative study of virgin and recycled polyethylene terephthalate and polypropylene intermingled thermoplastic composites. Polym Compos. 2024;46:3820–36. Karahan M, Abbas A, Hussain M. Commingled synthetic and natural fibers preforms reinforced composites: a simultaneous comparison of mechanical properties. Polym. Compos. 2025;46:10793–804. Friedman HL. Kinetics of Thermal Degradation of Char-forming Plastics from Thermogravimetry. J. Polym. Sci. Polym. Symp. 1964;6:183–95. Di Benedetto RM, Botelho EC, Gomes GF, Junqueira DM, Ancelotti Junior AC. Impact Energy Absorption Capability of Thermoplastic Commingled Composites. Compos. Part B Eng. 2019;176:1–29. Wendlandt, W. W. Thermal Analysis. (New York, 1985). Speil S, Berkelhamer LH, Pask JA, Davis B. Differential thermal analysis. Technol. Pap. 1945;664:81. Manson JAE, Wakeman MD, Bernet N. Composite Processing and Manufacturing—An Overview. Compr. Compos. Mater. 2000;2:577–607. Di Benedetto RM, Janotti AJ, Gomes GF, Ancelotti Junior AC, Botelho EC. Development of hybrid steel-commingled composites cf/peek/bwm by filament winding and thermoforming. Compos. Sci. Technol. 2022;218:1–20. Çuvalci H, Erbay K, İpek H. Investigation of the Effect of Glass Fiber Content on the Mechanical Properties of Cast Polyamide. Arab. J. Sci. Eng. 2014;39:9049–56. ASTM. ASTM D3171 Methods, For Standard Test Materials, Constituent Content of Composite. 1–10 at (1999). ASTM-D2734. Standard Test Methods for Void Content of Reinforced Plastics. 1994. ASTM. ASTM D3418 Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry. 107 at (2012). DARPA. MIL-A-46106, Military specification: adhesive-sealants, silicon, rtv, general-purposes. 1970, 1–25 at. Silvano TF, Di Benedetto RM, Sonego M, Souza A, Ancelotti Junior AC. DMA Master Curves for Long-Term Life Prediction of Epoxy Resins and Composites Using Time Temperature Superposition. Mater Res. 2025;28:1–12. Acknowledgements The authors acknowledge the financial support from National Council for Scientific and Technological Development (CNPq) under project 407431/2022‑5, 447331/2024‑8 and 303160/2023‑3; from Research Foundation of the State of Minas Gerais (FAPEMIG) under project APQ 01846-18, APQ 00853-25 and APQ 07473-25. The authors thank the Composite Technology Center (NTC) from the Federal University de Itajubá-Brazil for the general facilities. Funding National Council for Scientific and Technological Development (CNPq) under project 407431/2022‑5, 447331/2024‑8 and 303160/2023‑3; Research Foundation of the State of Minas Gerais (FAPEMIG) under project APQ 01846-18, APQ 00853-25 and APQ 07473-25. Author information Authors and Affiliations Institute of Mechanical Engineering, Federal University of Itajubá—UNIFEI, Composite Technology Center, Av. BPS, 1303, Itajubá, MG, Brazil Thiago de Freitas Silvano, Ricardo Mello Di Benedetto, Rubens Augusto Carvalho Rafanhim & Antonio Carlos Ancelotti Junior Department of Mechanical Engineering, Federal University of São João Del Rei, UFSJ, São João Del Rei, Brazil Tulio Hallak Panzera Department of Materials Science & Engineering, University of Delaware—UDEL, Newark, DE, USA Anderson Janotti Contributions Thiago de Freitas Silvano: Investigation, Validation, Writing - Original Draft, Data Curation Ricardo Mello Di Benedetto: Conceptualization, Writing - Review & Editing Anderson Janotti: Supervision, Writing - Review & Editing Rubens Augusto Carvalho Rafanhim: Methodology, Data Curation Tulio Hallak Panzera: Formal Analysis, Writing - Review & Editing Antonio Carlos Ancelotti Junior: Resources, Funding Acquisition, Supervision Corresponding author Correspondence to Thiago de Freitas Silvano. Ethics declarations Competing interests The authors declare no competing interests. Additional information Publisher’s Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. Rights and permissions Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law. About this article Cite this article de Freitas Silvano, T., Di Benedetto, R.M., Janotti, A. et al. Development of commingled hoop-wound composites-reinforced O-rings (CRO) for aeronautical application. Mech Compos Mater (2026). https://doi.org/10.1007/s11029-026-10423-w Received: Revised: Accepted: Published: Version of record: DOI: https://doi.org/10.1007/s11029-026-10423-w
原文出处:https://link.springer.com/article/10.1007/s11029-026-10423-w
提示:本站仅汇集公开信息,版权归原作者与原发布媒体所有。
P204 · P204-2