研究院科研情报与新闻主站科研动态 · 行业情报 · 管理政策
2026年11月17日
首页 › 生物化工 › 正文

Life-cycle-guided redesign of biocatalyst production enables greener conversion of textile microfibers into chiral chemi

RSC Publishing 2026-11-16 1 天前
Building on our previously developed biocatalytic route for converting PET-derived TPA into l-alanine (l-Ala) and d-alanine (d-Ala),6 industrially relevant chiral building blocks, here we move from demonstrating biochemical conversion to sustainability-guided process redesign. Household-derived PET–cotton microfibers were used as a dual feedstock in which PET-derived TPA supplies the carbon skelet
Paper| 16 November 2026 Newly published Life-cycle-guided redesign of biocatalyst production enables greener conversion of textile microfibers into chiral chemicals Open Access Elena Rosini † ; Elena Rosini † a The Protein Factory 2.0 Lab , Department of Biotechnology and Life Sciences , University of Insubria , Via J.H. Dunant 3 , 21100, Varese, Italy . Search for other works by this author on: Marco Carnevale Miino † ; Marco Carnevale Miino † b CLEAR Lab , Department of Theoretical and Applied Sciences , University of Insubria , Via O. Rossi 9 , 21100, Varese, Italy . Search for other works by this author on: Paolo Castelnovo † ; Paolo Castelnovo † c InsIDE Lab , Department of Economics , University of Insubria , Via Monte Generoso 71 , 21100 Varese, Italy . Search for other works by this author on: Vincenzo Torretta ; Vincenzo Torretta b CLEAR Lab , Department of Theoretical and Applied Sciences , University of Insubria , Via O. Rossi 9 , 21100, Varese, Italy . Search for other works by this author on: Andrea Vezzulli ; Andrea Vezzulli c InsIDE Lab , Department of Economics , University of Insubria , Via Monte Generoso 71 , 21100 Varese, Italy . Search for other works by this author on: Marco Mascheroni; Marco Mascheroni c InsIDE Lab , Department of Economics , University of Insubria , Via Monte Generoso 71 , 21100 Varese, Italy . Search for other works by this author on: Beatrice Luzi; Beatrice Luzi d Water Research Institute , National Research Council , Largo Tonolli 50 , Verbania, 28920, Italy . Search for other works by this author on: Silvia Galafassi ; Silvia Galafassi d Water Research Institute , National Research Council , Largo Tonolli 50 , Verbania, 28920, Italy . Search for other works by this author on: Rosa Zullo ; Rosa Zullo d Water Research Institute , National Research Council , Largo Tonolli 50 , Verbania, 28920, Italy . Search for other works by this author on: Loredano Pollegioni Corresponding Author Loredano Pollegioni a The Protein Factory 2.0 Lab , Department of Biotechnology and Life Sciences , University of Insubria , Via J.H. Dunant 3 , 21100, Varese, Italy . Search for other works by this author on: Publisher: The Royal Society of Chemistry Received: 02 September 2026 Accepted: 03 November 2026 First published: 16 November 2026 Online ISSN: 1463-9270 Print ISSN: 1463-9262 Funding Group: · Award Group: · Funder(s): Fondazione Cariplo · Award Id(s): 2022-0631 · Funder(s): · Award Group: · Funder(s): Università degli Studi dell'Insubria · Funder(s): · Award Group: · Funder(s): Consorzio Interuniversitario Biotecnologie · Award Id(s): CIB project 2024 “Nuove tendenze per le applicazioni biotecnologiche” · Funder(s): © 2026 The Author(s). Published by the Royal Society of Chemistry 2026 The Author(s) This article is licensed under a Creative Commons Attribution 4.0 Unported Licence. You can use material from this article in other publications without requesting further permissions from the RSC, provided that the correct acknowledgement is given. Green Chem. (2026) Article history Received: 02 September 2026 Accepted: 03 November 2026 First published: 16 November 2026 Citation Elena Rosini, Marco Carnevale Miino, Paolo Castelnovo, Vincenzo Torretta, Andrea Vezzulli, Marco Mascheroni, Beatrice Luzi, Silvia Galafassi, Rosa Zullo, Loredano Pollegioni; Life-cycle-guided redesign of biocatalyst production enables greener conversion of textile microfibers into chiral chemicals. Green Chem. 2026; https://doi.org/10.1039/d6gc05345a Download citation file: Open figure viewer Biocatalysis and waste-derived feedstocks are increasingly employed to reduce the environmental burden of chemical manufacturing, but neither inherently guarantees a greener process. Here, we combine experimental biocatalysis with life-cycle assessment to identify and redesign the dominant sustainability bottlenecks in the conversion of household-derived PET–cotton microfibers into enantiopure alanine. A 75/25 cotton/PET microfiber mixture was fractionated and valorized through cellulose hydrolysis, enzymatic PET depolymerization and a multistep biocatalytic cascade. Cellulose conversion reached 74.3 ± 3.7%, while PET depolymerization reached 92.8 ± 3.2%; the integrated process produced approximately 106 mg of l- or d-alanine per gram of textile microfibers. Life-cycle analysis revealed that biocatalyst production and downstream processing, rather than microfiber recovery, dominated the environmental footprint. Guided by this analysis, conventional intracellular recombinant enzyme production and chromatographic purification were replaced by vesicle-mediated extracellular production. Experimentally validated recombinant protein yields increased by approximately 40-fold while catalytic performance was maintained. Extending these improvements across the enzymatic cascade in a prospective scenario reduced the calculated environmental impact by approximately 81% and operational costs by 83–85%. These results demonstrate that catalyst manufacture can dominate the greenness of enzymatic waste valorization and establish sustainability-guided biocatalyst engineering as a strategy for designing lower-impact chemical processes. Green foundation 1. We demonstrate that biocatalyst manufacture can dominate the environmental performance of enzymatic waste valorization and show how life-cycle assessment can guide experimental redesign of catalyst production rather than merely evaluate a completed process. 2. Vesicle-mediated production increased the yield of three experimentally validated recombinant enzymes by approximately 40-fold while maintaining catalytic performance. Prospective extension across the cascade predicted approximately 81% lower environmental impact and 83–85% lower operational costs relative to the baseline process. 3. Further improvements should target a greener overall process through lower-temperature PET pre-treatment, reduced buffer and water demand, more efficient cofactor use, catalyst reuse, and experimental validation of vesicle-mediated enzyme production for the complete cascade and at larger scale. 1. Introduction Biocatalysis and waste-derived carbon are increasingly proposed as routes towards lower-impact chemical manufacturing. However, replacing fossil feedstocks with waste and employing enzymes as catalysts do not, by themselves, ensure that a process satisfies the objectives of green chemistry. Quantitative evaluation of the environmental burden associated with catalyst manufacture, process auxiliaries, and downstream operations is therefore essential for designing genuinely lower-impact bioprocesses. Among emerging waste feedstocks, household-derived textile microfibers are particularly attractive because they combine two chemically distinct carbon sources—polyethylene terephthalate (PET) and cotton—that are continuously generated during laundering and drying of blended textiles.1,2 PET, one of the most widely used textile polymers, represents a major component of synthetic microfiber emissions.3,4 Although household filtration technologies can efficiently intercept these emissions at the source,5 the recovered material is typically treated as waste rather than as a secondary feedstock for chemical production. Valorizing captured PET–cotton microfibers therefore offer an opportunity to couple pollution prevention with lower-impact chemical manufacturing. Recent advances in enzyme engineering and microbial biocatalysis have enabled the efficient depolymerization of PET and the conversion of its monomers into value-added chemicals.6,7 Mixed PET–cotton textiles are particularly attractive substrates because both polymer fractions can be valorized within an integrated biocatalytic process. However, while previous studies have established the biochemical feasibility of PET depolymerization, TPA upgrading, and integrated valorization of mixed PET–cotton substrates, process development has predominantly focused on polymer conversion, product yield, and monomer recovery. The contribution of recombinant biocatalyst manufacture and downstream enzyme processing to the overall environmental and economic performance of such multienzyme platforms has received comparatively limited attention. Although such approaches are conceptually aligned with circular bioeconomy principles,8 the sustainability of enzymatic waste valorization cannot be assumed. High catalyst loadings, recombinant protein production, chromatographic purification, buffer preparation, and cofactor requirements may offset the environmental benefits associated with waste-derived feedstocks. Integrating Life Cycle Assessment (LCA) with Life Cycle Costing (LCC) therefore provides a framework not only to evaluate emerging bioprocesses, but also to identify the technological interventions with the greatest potential for improving their green chemistry performance. Accordingly, recombinant biocatalyst productivity may represent not only a conventional bioprocess performance metric, but also a critical determinant of the environmental efficiency of enzymatic chemical manufacturing. Building on our previously developed biocatalytic route for converting PET-derived TPA into l-alanine (l-Ala) and d-alanine (d-Ala),6 industrially relevant chiral building blocks, here we move from demonstrating biochemical conversion to sustainability-guided process redesign. Household-derived PET–cotton microfibers were used as a dual feedstock in which PET-derived TPA supplies the carbon skeleton of the target chiral product and cotton-derived glucose supports biocatalyst production. LCA and LCC were then used to identify environmental and economic hotspots across the process, rather than solely to characterize its final performance.9 The dominant hotspot was experimentally targeted through vesicle-mediated recombinant enzyme production, allowing us to test whether improving biocatalyst manufacture could translate into a measurable green chemistry advance and to define the remaining priorities for further process greening. 2. Experimental 2.1. Recovery and analysis of microfibers Microfibers from 100% cotton and 100% PET textiles were recovered from a commercial tumble dryer. Approximately 3 kg of textile material were washed without detergent using an Electrolux washing machine (model EW9F116GREEN) under an “eco” washing programme at 40 °C, with a final spin cycle at 1400 rpm. Following washing, textiles were dried in an Electrolux tumble dryer (model EW9HW493) using a programme designed for synthetic textiles, applied to both cotton and PET materials. Microfiber release was assessed through the quantification of fibers retained in the dryer lint filter, which was thoroughly cleaned after each drying cycle. Quantification was performed gravimetrically by weighing the recovered material and normalising the results to the textile load, and expressed as mg fibers per kg of textile. The fibers collected from each cycle were visually inspected for impurities and contamination. Fourier-transform infrared (FTIR) spectroscopy was used to verify the polymeric composition of both the original textiles and the released fibers. Spectra were acquired with an IRAffinity-1S spectrometer (Shimadzu) equipped with an attenuated total reflectance (ATR) accessory over the range 4000–400 cm−1, with a spectral resolution of 4 cm−1 and 45 scans per spectrum. FTIR analysis was also used to assess possible polymer degradation during the process by comparing spectra from the unwashed textiles with those of fibres released during the drying cycle. Scanning electron microscopy (SEM) was performed on a Jeol JCM-7000 instrument to evaluate potential changes in fiber morphology after repeated washing and drying cycles. Fibers were mounted on aluminium stubs, sputter-coated with gold, and observed at an accelerating voltage of 10 kV under high-vacuum conditions. A total of ten consecutive washing and drying cycles were performed for each textile. Between successive experiments, one empty cleaning cycle of the washing machine was carried out, while the tumble dryer lint filter was thoroughly cleaned with a damp cloth and the accessible internal surfaces of the appliance were carefully vacuum-cleaned. To minimise contamination, the water used both for cleaning laboratory glassware and the experimental procedure was pre-filtered through GF/C glass fibre filters (Whatman). 2.2. Biotransformation 2.2.1. Thermo-mechanical pretreatments of textile fibers and enzymatic hydrolysis Polycotton samples were manually prepared by combining 100% cotton black microfibers with 100% PET light-blue microfibers, both recovered from a household dryer (see above), to obtain a final composition of approximately 75% cotton and 25% PET. The blended textile material was subjected to a sequential thermo-mechanical pretreatment and enzymatic hydrolysis approach adapted from the biotechnological platform developed by Zangelmi et al.7 (see Fig. 1). Briefly, 470 mg of textile material (approximately 350 mg cotton and 120 mg PET) were mechanically pretreated by ball milling using a PM100 planetary ball mill (Verder, Germany) equipped with a 500 mL zirconium oxide grinding jar containing ten zirconium oxide balls (20 mm diameter). Milling was performed at 10 Hz for 8 min under dry conditions to reduce fiber size and increase substrate accessibility for subsequent enzymatic hydrolysis. After milling, samples were washed with 0.1% (w/v) sodium dodecyl sulfate (SDS), thoroughly rinsed with Milli-Q water to remove detergent residues, washed with absolute ethanol, and dried at 30 °C. The pretreated samples were suspended in 50 mM sodium citrate buffer (pH 5.0) at a solid loading of 7.5% (w/v) and equilibrated overnight. Enzymatic hydrolysis was initiated by addition of commercial cellulase/hemicellulase cocktails, corresponding to approx. 14 FPU g−1 substrate. Reactions were incubated at 55 °C for 24 h under continuous agitation. Following cellulase treatment, soluble hydrolysis products were recovered in the liquid phase. Glucose concentration was determined by high-performance liquid chromatography (HPLC) using a PRONTOGEL H column coupled to a refractive index detector, according to the analytical method described by Zangelmi et al.7 Glucose release was used to estimate cellulose conversion by applying the stoichiometric correction factor (0.90) to account for the mass difference between anhydroglucose units in cellulose and free glucose.7,10 The residual PET solid fraction was manually recovered and thermally pretreated by placing the material between two 0.1 mm polytetrafluoroethylene (PTFE) sheets on a hot plate at 290 °C. Once the polymer had completely melted, a 500 g stainless-steel cylinder was applied to form a thin film. After 15 min, samples were rapidly quenched in an ice-water bath, washed with Milli-Q water, and dried at 30 °C. This treatment was applied to reduce PET crystallinity and enhance the efficiency of the subsequent enzymatic depolymerization. Enzymatic PET depolymerization was carried out in 50 mL Falcon tubes containing approximately 120 mg of the thermally pretreated PET fraction, 10 mL of 100 mM potassium phosphate buffer (pH 8.0), and 120 μg (13 U) of the engineered S101N/F243T-ΔLCC (or VNp_S101N/F243T-ΔLCC, see below) variant.6 Reaction mixtures were incubated at 55 °C for 24 h under continuous rotation, as previously described.7 PET hydrolysis products were quantified by HPLC using a Symmetry C18 column with UV detection at 240 nm, following the previously optimized analytical procedure.7 All experiments were performed in triplicate. 2.2.2. Development and production of the whole-cell biocatalyst and recombinant enzymes The biocatalytic cascade employed in this study for the conversion of TPA obtained from enzymatic depolymerization of the PET fraction of polycotton textiles, into enantiopure l- or d-Ala was based on the synthetic pathway previously developed (Fig. 1).6 2.2.2.1. Whole-cell preparation The K-12 MG1655 RARE E. coli strain was transformed with three Duet series plasmids which contain the genes encoding the enzymes terephthalate dioxygenase α and β subunits (TPADOα/β), the associated reductase (TPADO RED), the 1,2-dihydroxy-3,5-cyclohexadiene-1,4-dicarboxylate dehydrogenase (DCDDH), the protocatechuate 4,5-dioxygenase (LigAB), and the 4-carboxy-2-hydroxymuconate-6-semialdehyde dehydrogenase (LigC), required for the bioconversion of TPA into 2-pyrone-4,6-dicarboxylic acid (PDC) (strain D).6 For the present study, the strain D was grown in LB autoinduction medium supplemented with ampicillin (100 μg mL−1), kanamycin (50 μg mL−1), and streptomycin (50 μg mL−1). Protein expression was induced by the addition of 2.0 g L−1 lactose, while the carbon source consisted of 0.5 g L−1 glucose recovered from the cellulase-mediated hydrolysis of the cotton fraction of polycotton textiles, as described in section 2.2.1. The glucose-containing hydrolysate was used directly to supplement the culture medium without further purification. Cultures were incubated at 30 °C with orbital shaking for 21 h. Cells were harvested by centrifugation at 7650g for 10 min at 4 °C, washed with reaction buffer (100 mM Tris-HCl, 10% (v/v) glycerol, pH 7.0), and resuspended to a final concentration of 500 mg cell wet weight (cww) per mL. Resting cell suspensions were stored at 4 °C. 2.2.2.2. Production of recombinant enzymes The downstream enzymes LigI, LigJ, LigU, and LigK, which catalyze the sequential conversion of PDC into pyruvate, were produced as recombinant proteins. The pyruvate generated by the tandem approach (see below) was subsequently converted into enantiopure l- or d-Ala using two recombinant NADPH-dependent amino acid dehydrogenases previously described:6 the D196A/L197R variant of alanine dehydrogenase from Bacillus subtilis (BsAlaDH), and the meso-diaminopimelate dehydrogenase from Symbiobacterium thermophilum (St_mDAPDH). Detailed expression conditions, purification yields, and biochemical characterization data are provided in Rosini et al.6 2.2.2.3. Construction of the VNp_S101N/F243T-ΔLCC, VNp_LigJ and VNp_St_mDAPDH expression vectors, recombinant vesicle production, and protein recovery The DNA sequences encoding the S101N/F243T-ΔLCC variant, the LigJ and the St_mDAPDH enzymes6 were inserted downstream of the vesicle nucleating peptide (VNp)11 in the pET29_VNp-His6 expression vector using the BglII and KpnI restriction sites, yielding an in-frame fusion with the N-terminal VNp tag and a C-terminal hexahistidine tag. The resulting plasmids, pET29_VNp_ S101N/F243T_ΔLCC, pET29_VNp_LigJ and pET29_VNp_ST_mDAPDH were introduced into chemically competent E. coli BL21(DE3) cells for recombinant protein production. For protein expression, a 5 mL LB starter culture containing kanamycin (50 μg mL−1) was inoculated with freshly transformed colonies and incubated at 37 °C until saturation. The preculture was used to inoculate 25 mL of Terrific Broth (0.4 mL L−1 glycerol) supplemented with kanamycin in 500 mL Erlenmeyer flasks to ensure efficient aeration. Cultures were grown at 37 °C with orbital shaking (200 rpm) until the optical density at 600 nm reached 0.8–1.0. Recombinant protein production was induced by adding isopropyl-β-d-1-thiogalactopyranoside (IPTG) to a final concentration of 84 μM, and incubation was continued for 18 h at 30 °C. Cells were collected by centrifugation at 3000g for 20 min at 4 °C. Extracellular vesicles containing the recombinant fusion protein were isolated by filtering the culture supernatant through a 0.1 μm polyethersulfone membrane. The retained material was recovered by rinsing the membrane with 1.5 mL phosphate-buffered saline (PBS) and gently scraping the surface. To release the recombinant protein, vesicle suspensions were disrupted by sonication (six cycles of 20 s with c
原文出处:https://pubs.rsc.org/gc/article/doi/10.1039/d6gc05345a/1381655/Life-cycle-guided-redesign-of-biocatalyst
提示:本站仅汇集公开信息,版权归原作者与原发布媒体所有。
P204 · P204-2